1394 South Third Street, Mebane NC 27302
1-800-880-6788 • www.kiddeus.com
Architectural and Engineering
Specifications
The heat detector shall be Kidde Unit HD135F or approved
equal. It shall be powered by a 120VAC, 60Hz source along
with a 9V battery backup. The temperature operation range
shall be between 40°F and 100°F (4°C and 38°C) and the
humidity operation range shall be 5% - 95% relative humidity.
The heat detector can be installed on any standard single
gang electrical box, up to a 4” octagon junction box. The
electrical connection (to the alarm) shall be made with a
plug-in connector. A maximum of 24 Kidde devices can be
interconnected in a multiple station arrangement. The inte
connect system must not exceed the NFPA (National Fire
Protection Association) limit of 18 initiating devices (Smoke,
heat, CO, etc) interconnected, it is still possible to intercon-
nect 6 strobe lights and or relay modules. The alarm shall
provide optional tamper resistance that deters removal of the
unit from the wall or ceiling.
The unit shall include a piezoelectric horn that is rated at
85dB at 10ft. The unit shall incorporate a LED. A red LED will
be constantly “ON” when AC power is present and will flash
once approximately every 30-40 seconds to indicate that the
smoke alarm is operating properly and will flash rapidly
when the unit is alarming and will remain so until the air is
cleared.
The unit shall incorporate a test button. The test button
shall test all the electronic circuitry, horn, and battery.
The unit shall at a minimum meet the requirements of
UL217, NFPA72, (chapter 10 & 11 2002 edition) The State of
California Fire Marshall, NFPA101 (One and two family
dwellings, Federal Housing Authority (FHA), Housing and
Urban Development (HUD).
Installation of Heat Detector
The heat detector should be installed to comply with all local
codes having jurisdiction in your area, Article 760 of the
National Electric Code, and NFPA 72. Make certain all alarms are
wired to a single, continuous (non-switched) power line, which
is not protected by a ground fault interrupter. A maximum of
1000 ft. of wire can be used in the interconnect system.
120VAC Wire In with 9V Battery Back Up
Heat Detector
Unit Number HD135F
Technical Specifications
Unit Number: HD135F
UPC: 0-25417-84135-0
Power Source: 120VAC, 60HZ, 9V battery backup
Sensor: Heat
Audio Alarm: 85dB at 10ft
Temperature Range: 40˚F to 100˚F (4˚C to 38˚C)
Humidity Range: 5%-95% relative humidity (RH)
Size: 5” in diameter x 2” depth
Weight: .75lbs
Interconnects: Up to 24 Kidde devices
LED: Red, AC power present,
alarm mode
Warranty: 5 year limited warranty
Distributed by:
Ordering Information
Gift Box UPC: 0-25417-84135-0
Part Dimensions Case/ Layers/ Skid
Number I 2 of 5 Pack Quantity (w x d x h inches) Weight Skid Skid Weight
HD135F N/A Individual 4.75 x 2.45 x 5.65 .75lbs N/A N/A N/A
HD135F 200 25417 84135 4 Master Pack (6 units) 6.5 x 10.5 x 6.5 4.5lbs 60 5 270lbs
(6 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels